Home / Picture / DCM-PRO Cable
When should I check my resistance readings for the DCM-PRO cables?
DCM-PRO Cable
Check Resistance Readings for DCM-PRO Cables
Check the resistance of the heating cable before, during and after installation to make sure the heating cable is not damaged. Use these resistance readings to register your warranty. The value should match the rating label found on the product within 5%.
Further Questions?
-
Installation
- What are the electrical requirements for my Warmup system?
- How do I check if the cable is working ?
- Can I install directly onto durock or hardieboard?
- How far away from the wall should floor heat be installed?
- Can I cross floor heating cables?
- How many packages of fixing strips do I need?
- How long after flooring installation should we wait to use the heat?
- Can you install over tile?
- How do I register a product warranty?
- Can I install directly onto durock or hardieboard?
- Does Warmup restrict tile size?
- What can I do if I do not have enough cable?
- Is there a video guide for installing the DCM-PRO system?
- What system works best with tile flooring?
- How do I test my heating cable(s)?
- Comment tester mon (mes) câble(s) chauffant(s) ?
- What is the difference between a Watch Dog and an Alligator?
- What is the diameter of the DCM-PRO cable?
- Is it possible to put less leveler over the membrane?
- Can the cable be spaced at 2 pegs?
- Does having a membrane change the cure time?
- Which thin set is recommended in Québec?
- What type of thin set can be used with the DCM-PRO system?
- Should I use primer?
- Should I leave space between membrane sheets?
- How do I know which voltage to run to my DCM-PRO cables?
- When should I check my resistance readings for the DCM-PRO cables?
- Where do I install the DCM-PRO Factory Joint?
- How long is the cold lead on the DCM-PRO cable?
- Where do I run the cold lead and sensor probe during DCM-PRO installation?
- What is the correct DCM-PRO cable spacing?
- Can the cold tail lead of your Warmup indoor heating system be extended?
- Can the lead of your Warmup heating system be trimmed?
-
Troubleshooting
- What are the electrical requirements for my Warmup system?
- Can I have a technician come to my home?
- How does the infrared thermal camera work?
- How do I test my heating cable(s)?
- Comment tester mon (mes) câble(s) chauffant(s) ?
- What is the difference between a Watch Dog and an Alligator?
- How to Check the Resistance Readings of your Electric Floor Heating System
-
Miscellaneous questions
- How Long will my Electric Floor Heating System Take to Heat Up?
- Can I use area rugs with underfloor heating?
- What is an uncoupling system?
- How much does underfloor heating cost to operate?
- What does the DCM-PRO Warranty Cover?
- Will the membrane keep it’s decoupling capability over time?
- When should I check my resistance readings for the DCM-PRO cables?
- What is the DCM-PRO cable made of?
-
Preparing for your project
- How Long will my Electric Floor Heating System Take to Heat Up?
- What product do I use if I need 110V?
- How many packages of fixing strips do I need?
- Can floor heating be used as a primary heat source?
- Can I heat under furniture?
- How thick is DCM-PRO?
- What system works best with tile flooring?
- How do Floor Heating Systems Work?
- What is the diameter of the DCM-PRO cable?
- Calculating Heat Loss: How many BTU’s are in a watt?
- When should I check my resistance readings for the DCM-PRO cables?
- How long is the cold lead on the DCM-PRO cable?
- Where do I run the cold lead and sensor probe during DCM-PRO installation?
-
Wiring
- Can you wire floor heat for 120 or 240 volt?
- What gauge wire should be used?
- What is the difference between a Watch Dog and an Alligator?
- How to Check the Resistance Readings of your Electric Floor Heating System
- How do I know which voltage to run to my DCM-PRO cables?
- Where do I run the cold lead and sensor probe during DCM-PRO installation?